Looking for a combination of LiPO charger, gauge and buck/boost
Hello,I am looking for a power management solution for my uC board that has a 3.7 V LiPo power supply. I need a 3.3 V output with a max current draw of 500 mA, and a battery gauge, as well as a USB...
View ArticleTPS62420 Settling Time
Require 1.85V for CC3200 in pre-regulated mode. Line and load regulation with less than 2% ripple, 500 mA step current and settling time of < 4 μs with the load step. Therefore changed from...
View ArticleWEBENCH® Tools/CC2640R2F: power supply design for my embedded system
Part Number:CC2640R2FTool/software: WEBENCH® Design Toolsmy embedded system contains:CC2640R2F - 1.8V and 0.03Amodule A - 1.8V and 0.2AModule B - 1.8V and 0.002Amodule C - 1) 3.3V and 0.4A2) 3.3V and...
View ArticleADC12DJ3200: Power supply desig for 3 ADCs
Part Number:ADC12DJ3200Hi TI Team,We are planning to use ADC12DJ3200 and DAC38RF80 in our design of data acquisition. We will be using three Nos. of ADC12DJ3200 and DAC38RF80.There will be separate...
View ArticleClik here to view.
Do all rails need low Iq?
All designers of ultra-low power systems are concerned about battery life. How much time will elapse before the battery in a fitness tracker will need recharging? Or, for primary cell systems, how long...
View ArticleMSP430G2553: SLAA604
Part Number: MSP430G2553Hi, We are using MSP430G2553 in our design. We are implementing a floating buck convertor in our design. We can across the following application note in TI website. We see the...
View ArticleClik here to view.
3 quiescent-current (Iq) specifications you need to understand
Other Parts Discussed in Post: TPS62840, BQ21061, BQ25120, TPS61094, TPS61099A common definition of quiescent current (IQ) is the current drawn by an integrated circuit (IC) in a no-load and...
View ArticleClik here to view.
Efficiently Power that Op Amp
Efficiency versus load current with Vout = -5VIn many applications, such as temperature sensing, two supply voltages are needed to power an op amp in the system—one positive and one negative. This...
View ArticleDAC53608: Design Tool for Output Voltage Adjustment using a DAC - SLVC780
Part Number: DAC53608Other Parts Discussed in Thread: TPS62088Hello all!I'm reaching out to the wider and more experienced audience to see if anyone has experience with using the Excel based design...
View ArticleTPS62420 Settling Time
Other Parts Discussed in Thread: TPS62420, TPS62421, CC3200, TPS62080, TPS62085Require 1.85V for CC3200 in pre-regulated mode. Line and load regulation with less than 2% ripple, 500 mA step current...
View ArticleClik here to view.
Extend the life of your coin cell with boost + bypass operation!
Picture this--You are designing your company’s latest and greatest water meter and have been asked to increase its battery’s run time by 10% over the previous model. This is now the fourth product...
View ArticleADC12DJ3200: Power supply desig for 3 ADCs
Part Number: ADC12DJ3200Other Parts Discussed in Thread: DAC38RF80, TPS62085, TPS7A7200, TPS62827, TPS62136, TPS63710, TPSM82480, TPS62180, TPS543B20, TPS543C20, TPS548D22, TPS548B22, TPS549D22,...
View ArticleClik here to view.
3 Keys to Ultra-Low-Power in Wearable Designs
Looking to develop a wearable device, such as a watch, oximeter, or blood pressure monitor? The small size and high functionality required in a smart watch pose two basic challenges to the system...
View ArticleMSP430G2553: SLAA604
Part Number: MSP430G2553Hi, We are using MSP430G2553 in our design. We are implementing a floating buck convertor in our design. We can across the following application note in TI website. We see the...
View Article